| HPBCANADA.COM http://ww.w.hpbc.ca/ |
|
| who cuts props? http://ww.w.hpbc.ca/viewtopic.php?f=19&t=1613 |
Page 1 of 1 |
| Author: | BoomerMuskoka [ September 7th, 2013, 1:20 pm ] |
| Post subject: | who cuts props? |
i have 3 choppers one 28p mach3 has been nicked, 1-merc 24p a4 look like it was nicked then repaired, other is 26p small ear chopper in desent shape,.. can someone cut them into something fancy for my valero, , if so who, and what does that cost?  or can i do it myself 
|
|
| Author: | allstock [ September 7th, 2013, 2:40 pm ] |
| Post subject: | Re: who cuts props? |
BoomerMuskoka wrote: i have 3 choppers one 28p mach3 has been nicked, 1-merc 24p a4 look like it was nicked then repaired, other is 26p small ear chopper in desent shape,.. can someone cut them into something fancy for my valero, , if so who, and what does that cost? or can i do it myself Boomer, you know the answer. John at Kawartha prop. |
|
| Author: | Northbase [ September 7th, 2013, 4:20 pm ] |
| Post subject: | Re: who cuts props? |
Steve Smith. SDS prop works Shepherdsville Kentucky. Awesome work!! You can find him on S&F, goes by the name DS77 |
|
| Author: | AnthonySS [ September 7th, 2013, 9:15 pm ] |
| Post subject: | Re: who cuts props? |
Another thumbs up for SDS Props...he has done a few for me this year 
|
|
| Author: | BoomerMuskoka [ September 8th, 2013, 9:56 am ] |
| Post subject: | Re: who cuts props? |
Northbase wrote: Steve Smith. SDS prop works Shepherdsville Kentucky. Awesome work!! You can find him on S&F, goes by the name DS77 i'll check him out.. Thanks 
|
|
| Author: | Northbase [ September 8th, 2013, 10:11 am ] |
| Post subject: | Re: who cuts props? |
BoomerMuskoka wrote: Northbase wrote: Steve Smith. SDS prop works Shepherdsville Kentucky. Awesome work!! You can find him on S&F, goes by the name DS77 i'll check him out.. Thanks He also does amazing gear case work...... But I think yours may be a little far gone.
|
|
| Author: | BoomerMuskoka [ September 8th, 2013, 12:14 pm ] |
| Post subject: | Re: who cuts props? |
| it has seen better days,, it was an old case and i hear it might of been hard to weld, the newer cases are a better cast aluminum,  ,so i went and found an 2006 case, to work on this winter, still have to take my old case up to dok to see if the guts are salvageable,  and i have a bunch of props to play with when all of this is said and done,  24p A5 chopper, 26p small ear chopper, 28p mach 3 chopper and a purdy lookin' 32p performer ET where in ta f**n states, is my lwp
|
|
| Author: | idvette [ September 8th, 2013, 12:16 pm ] |
| Post subject: | Re: who cuts props? |
So what are you doing with that Mach 3???? If you need to get I wet, I know of a boat that might work for it..... |
|
| Author: | BoomerMuskoka [ September 8th, 2013, 12:28 pm ] |
| Post subject: | Re: who cuts props? |
idvette wrote: So what are you doing with that Mach 3???? If you need to get I wet, I know of a boat that might work for it..... the mach 3 was my favorite prop i dunno who worked it but its been ground on and it pulled hard, it has a little nick from when the case exploded, but im sure can be touched up eazy enough, i hope to run it once again, i got it from paul ,, you can borrow it if you want, ,.. i think the 26p would be bad ass prop on your boat,, it needs the weed whackers cut off,,, it pulled hard too but didnt lauch the best on my boat, and i havent tryed it with a drag plate so that might help it out..
|
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| © 2000, 2002, 2005, 2007 phpBB Group • http://www.phpbb.com | |