HPBCANADA.COM
http://ww.w.hpbc.ca/

Yamaha ProV115
http://ww.w.hpbc.ca/viewtopic.php?f=19&t=2705		 Page 1 of 4
Author:  DoktorC [ February 28th, 2015, 2:38 pm ]
Post subject:  Yamaha ProV115
I finally decided to drag the old girl into the basement where it's warm and make it into something useful. This is going in the 16 DL I bought last winter and will be used on the lake here at the house for dragging the kids around the lake.

I bought the motor from RBT...it was a sinker...so with some JUNK from The Gun I hope it'll be a cheap motor for my kids to wreck lol.

So I started by pulling the sleeves and installing a set of excel sleeves that I scrounged from Boomer

Image

Image

Got the crank and pistons in...I even found a set of new yamaha rings.

Image

Image


Short block all buttoned up...still have to clean the gaskets on the heads but it's getting closer..
Image

Image
Author:  LittleCharger [ February 28th, 2015, 2:49 pm ]
Post subject:  Re: Yamaha ProV115
Nice dok! That will be a real nice combination. Can't wait to see Mitchie take the first tube run.
Author:  DoktorC [ February 28th, 2015, 2:54 pm ]
Post subject:  Re: Yamaha ProV115
LittleCharger wrote:
Nice dok! That will be a real nice combination. Can't wait to see Mitchie take the first tube run.


I'm going to have to check my tripod rating lol.
Author:  OneCycle [ February 28th, 2015, 8:13 pm ]
Post subject:  Re: Yamaha ProV115
Are excell sleeves diffrent than the stock v4 ones ? Did you do it for performance gains?
Author:  DoktorC [ February 28th, 2015, 8:17 pm ]
Post subject:  Re: Yamaha ProV115
OneCycle wrote:
Are excell sleeves diffrent than the stock v4 ones ? Did you do it for performance gains?


Yup :mrgreen:
Author:  LittleCharger [ March 1st, 2015, 10:18 am ]
Post subject:  Re: Yamaha ProV115
DoktorC wrote:
OneCycle wrote:
Are excell sleeves diffrent than the stock v4 ones ? Did you do it for performance gains?


Yup :mrgreen:


Nothing ever comes out of that shop stock! Cheat'n yamaha guys
Author:  OneCycle [ March 1st, 2015, 10:22 am ]
Post subject:  Re: Yamaha ProV115
LittleCharger wrote:
DoktorC wrote:
OneCycle wrote:
Are excell sleeves diffrent than the stock v4 ones ? Did you do it for performance gains?


Yup :mrgreen:


Nothing ever comes out of that shop stock! Cheat'n yamaha guys



Yeah tell me about it.... Why even modifiy a yamaha... Just buy a merc and start off where the yamaha ends up..... :shock:
Author:  DoktorC [ March 1st, 2015, 10:29 am ]
Post subject:  Re: Yamaha ProV115
OneCycle wrote:
LittleCharger wrote:
DoktorC wrote:
OneCycle wrote:
Are excell sleeves diffrent than the stock v4 ones ? Did you do it for performance gains?


Yup :mrgreen:


Nothing ever comes out of that shop stock! Cheat'n yamaha guys



Yeah tell me about it.... Why even modifiy a yamaha... Just buy a merc and start off where the yamaha ends up..... :shock:


My yamaha's never end up in the scrap bin..
:mrgreen:

Some start there though lol
Author:  BoomerMuskoka [ March 1st, 2015, 9:42 pm ]
Post subject:  Re: Yamaha ProV115
:lol: looks pretty slick dok, did you have to do any grinding behind the sleeve to match the ports,, i cant wait to see this one go
Author:  beavertonae-21 [ March 2nd, 2015, 9:22 am ]
Post subject:  Re: Yamaha ProV115
looking good Rick. I will have some questions this summer. Going to refresh my Excell one of these days.
Page 1 of 4 All times are UTC - 5 hours [ DST ]
© 2000, 2002, 2005, 2007 phpBB Group • http://www.phpbb.com