It is currently November 24th, 2024, 8:10 am

Blowout ring ? what is it

View active topics

All times are UTC - 5 hours [ DST ]


Post new topic Reply to topic  [ 9 posts ] 
Author Message
 PostPosted: October 17th, 2015, 7:41 am   
Member
User avatar

Joined: September 15th, 2015, 2:35 pm
Posts: 392
Location: Slough, England UK
Blow out ring ?
in the parts for sale I noticed there is a sst60 gearbox, prop and blowout ring !!!!
I have heard of these before but never seen one or know what it does or how it fits.

Could someone please give me info on these and do they actually work to help stop blowout on
holeshot or just top end .

pics would be good too.

cheers


Last edited by phillnjack on October 17th, 2015, 11:18 am, edited 1 time in total.

Top
 Profile Send private message  
 PostPosted: October 17th, 2015, 9:17 am   
Team Member
User avatar

Joined: July 13th, 2012, 6:57 pm
Posts: 521
Location: Little Britain, ON
It a ring that attaches to the gear case trailing edge usually with set screws which effectively lengthens the case.
Only useful at higher speeds when "blowout" or loss of propeller bite occurs once past design capability of lower unit. The variables are endless but we're usually referring to speed in excess of 80 Mph.


Top
 Profile Send private message  
 PostPosted: October 17th, 2015, 10:25 am   
Member
User avatar

Joined: September 15th, 2015, 2:35 pm
Posts: 392
Location: Slough, England UK
Cheers Tomcat
But what is the ones for over hub cleaver props and how do they fit ?
I tried Google and that came up with some very strange stuff, but nothing about
the blow out rings for cleaver props.
the advert for the sst60 gearbox shows something that to me looks like it goes over
the blades !!!!
I am probably seeing this ass about face and getting wrong impression.

ive heard /read of people using blow out rings to get better holeshot ? or is this wrong.

I read somewhere this morning about a blowout ring being used with an SRX !!!
again these are over hub props.
I saw a bit about rings being attached to smaller hub props to make them like a large
hub, yeah that I totally get.

need to get a better pic of the ring advertised with the prop.

I just wondered if it would help me get on plane with a SRX instead of the 1/4 mile it takes now.
.


Top
 Profile Send private message  
 PostPosted: October 17th, 2015, 1:13 pm   
Team Member
User avatar

Joined: July 13th, 2012, 6:57 pm
Posts: 521
Location: Little Britain, ON
Blowout rings are gear case specific and won't help your planing problem
Here's a pic…
http://www.screamandfly.com/showthread. ... =blow+ring
Can't think of anything that actually attaches to a prop and wouldn't want one. Some props have adjustable vent holes in the hub but that's not what you're referring to.

Sound to me like you're spinning too much prop and can't get it to bite, a planing issue.
Have a look at Smart Tabs here…
http://www.nauticusinc.com


Top
 Profile Send private message  
 PostPosted: October 17th, 2015, 7:34 pm   
Member
User avatar

Joined: September 15th, 2015, 2:35 pm
Posts: 392
Location: Slough, England UK
no i am not talking about vent holes in a prop, i have been venting props for 20 years or so.
i am talking about the rings sleeves or whatever you call them for over hub props.
just like the one that is in the parts for sale under sst60 gearbox and prop.

i have seen blow out rings that attach to the normal thru hub props, in both metal and the cheapy plastic ones held on my little grub screws etc.

the blowout rings i need to know about are for over hub cleavers.
there was a bit about them on BRF i read ages ago and also about special thrust washers that done almost the same job.
that was before i got a srx so didn't pay too much attention.

look below and see what i mean.

Image


Top
 Profile Send private message  
 PostPosted: October 17th, 2015, 7:37 pm   
Team Member
User avatar

Joined: July 13th, 2012, 6:57 pm
Posts: 521
Location: Little Britain, ON
Never seen one in these parts.
You're on your own there.


Top
 Profile Send private message  
 PostPosted: October 17th, 2015, 7:39 pm   
HPBC PRESIDENT
User avatar

Joined: March 31st, 2012, 5:53 pm
Posts: 3548
Location: Lapping lil charger
It basically makes your overhub prop a thru hub...

_________________
08 SRV w/3.1 Hydro-tec Phase lll

I've got enough torque to tear a hole....in time...


Top
 Profile Send private message  
 PostPosted: October 17th, 2015, 8:13 pm   
Team Member
User avatar

Joined: April 3rd, 2012, 7:53 pm
Posts: 406
Location: Lakeport, MI
blow out hubs stop blowout and give you an extra pin of trim and tail lift. we use one all the time.
http://www.screamandfly.com/showthread. ... Jeff-Titus


Top
 Profile Send private message WWW  
 PostPosted: October 17th, 2015, 9:21 pm   
Member
User avatar

Joined: September 15th, 2015, 2:35 pm
Posts: 392
Location: Slough, England UK
anyone got more pics of them.
would love to see a bit more about them.


Top
 Profile Send private message  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 9 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 55 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  


Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Style originally created by Volize © 2003 • Redesigned SkyLine by MartectX © 2008 - 2010