Dok sent me a pic of his new carbs he's put on for this race season, said he paid a lot of money to get them shipped from Japan, apparently they were only available for one year on commercial motors.
| HPBCANADA.COM http://ww.w.hpbc.ca/ |
|
| Dok's new carbs http://ww.w.hpbc.ca/viewtopic.php?f=19&t=3238 |
Page 1 of 2 |
| Author: | LittleCharger [ February 12th, 2016, 10:12 pm ] |
| Post subject: | Dok's new carbs |
Dok sent me a pic of his new carbs he's put on for this race season, said he paid a lot of money to get them shipped from Japan, apparently they were only available for one year on commercial motors.
|
|
| Author: | DoktorC [ February 12th, 2016, 11:14 pm ] |
| Post subject: | Re: Dok's new carbs |
64mm measured with bbq tongs... Gonna need some bigger fuel line that's all I'm gonna say.. |
|
| Author: | Hevi Kevi [ February 12th, 2016, 11:37 pm ] |
| Post subject: | Re: Dok's new carbs |
What year were the tongs? Home Hardware or Canadian Tire? I heard somewhere in 2013 the Canadian Tire ones had accuracy problems? You Yamaha guys and your metric system... Always messes me up? |
|
| Author: | DoktorC [ February 12th, 2016, 11:44 pm ] |
| Post subject: | Re: Dok's new carbs |
On another note I also safety wired my hood latches...one can never be too safe. |
|
| Author: | Hevi Kevi [ February 13th, 2016, 12:09 am ] |
| Post subject: | Re: Dok's new carbs |
Did you use the 6 hole system or the 4 hole system? I've seen plenty of guys have the 4 hole system rip right off at 37mph! I usually like to take the lid off a dumpster and use it for a windshield. I tested it all the way to 42mph and the hood didn't come off! |
|
| Author: | DoktorC [ February 13th, 2016, 12:14 am ] |
| Post subject: | Re: Dok's new carbs |
I'm more worried about the hood coming loose in the pits.....prying eyes and all that lol. |
|
| Author: | LittleCharger [ February 13th, 2016, 12:33 am ] |
| Post subject: | Re: Dok's new carbs |
Any thoughts on upgrading your jack plate with the expected increase in hp? |
|
| Author: | OneCycle [ February 13th, 2016, 8:40 am ] |
| Post subject: | Re: Dok's new carbs |
Your 300hp rated aluminum jack plate is junk now. You will bend it like an English pretzel . You should upgrade. |
|
| Author: | LittleCharger [ February 13th, 2016, 9:03 am ] |
| Post subject: | Re: Dok's new carbs |
No worries Geigertec is on it, Bryan fired up the plasma cutter last night and with The Gun welding he thinks he should save Ricky a little weight off the ass end at the end of the day. Win-win I'd say! Gig said he's gonna build RBT's new mid out of the same material!  
|
|
| Author: | phillnjack [ February 13th, 2016, 9:38 am ] |
| Post subject: | Re: Dok's new carbs |
you seriously have no idea how many jack plates have broken and sheared off ? and you all think your jack plates are "made in the usa " now that is dangerous. |
|
| Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
| © 2000, 2002, 2005, 2007 phpBB Group • http://www.phpbb.com | |