| HPBCANADA.COM http://ww.w.hpbc.ca/ |
|
| Mercury swivle angle? http://ww.w.hpbc.ca/viewtopic.php?f=19&t=658 |
Page 1 of 2 |
| Author: | p man [ October 22nd, 2012, 11:43 pm ] |
| Post subject: | Mercury swivle angle? |
Weird question I know How many degrees will a Merc 2.5 swivle turn? My problem is that my string steering leads come out of the boat 49" apart and stock Allison wingplates are 30" apart. This cause the line to bind up when I turn. The drum is trying to pull in more cable then is will let out. I need to figure out the geometry so that the line will not bind up or slack during regular turning. I know that the leads are all supposed to be parallel and attatch on the plane of the pivot tube but I am not putting 50" wingplate on my boat lol I figure that if I extend the attachment point on the wingplate 2.5" out AND 2.5" back it should work. From the #'s i put on paper I shouldn't have an issue up to 45 degrees but off the top of my head I don't know what lock to lock is on an offshore swivle. anyone have a clue??? |
|
| Author: | OneCycle [ October 23rd, 2012, 12:35 am ] |
| Post subject: | Re: Mercury swivle angle? |
love your sig pic.... the contrast between everything is sweet!! |
|
| Author: | p man [ October 23rd, 2012, 9:30 am ] |
| Post subject: | Re: Mercury swivle angle? |
Thank you James, some guy I know took it with a FujiFilm disposable |
|
| Author: | Jeff Yammer [ October 23rd, 2012, 10:10 am ] |
| Post subject: | Re: Mercury swivle angle? |
I might still have a copy of a Merc 15" "Shop drawing" that shows all the measurements and lengths. I'll look tonight P I think it's 90* in total. Most likely that's wrong though. I'm guessing you're not at the boat to measure it |
|
| Author: | OneCycle [ October 23rd, 2012, 11:49 am ] |
| Post subject: | Re: Mercury swivle angle? |
p man wrote: Thank you James, some guy I know took it with a FujiFilm disposable those Fuji's are top notch. i would challenge anyone to find a better camera. |
|
| Author: | Jeff Yammer [ October 23rd, 2012, 5:42 pm ] |
| Post subject: | Re: Mercury swivle angle? |
No luck sir. Can't find my sheets for that. I'd think TopGun has all the shop drawing type specs in the full shop service manuals. |
|
| Author: | Tomcat [ October 23rd, 2012, 9:43 pm ] |
| Post subject: | Re: Mercury swivle angle? |
If you can wait til tomorrow I can go out and measure it on my Ally. The powerhead is off so it should be easy. I take it you want total degrees stop to stop. Tom |
|
| Author: | p man [ October 24th, 2012, 12:16 am ] |
| Post subject: | Re: Mercury swivle angle? |
Tomcat wrote: If you can wait til tomorrow I can go out and measure it on my Ally. The powerhead is off so it should be easy. I take it you want total degrees stop to stop. Tom That would be great if you have a moment. Thank you. Just looking for what degree the motor turns to one way if straight is 0 degrees. |
|
| Author: | Tomcat [ October 24th, 2012, 9:02 am ] |
| Post subject: | Re: Mercury swivle angle? |
And the measurement is .... 30 degrees from center each direction. Checked a couple of mids, same on both. Tom |
|
| Author: | p man [ October 24th, 2012, 9:24 am ] |
| Post subject: | Re: Mercury swivle angle? |
That's great. Thank you so much for the help. |
|
| Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
| © 2000, 2002, 2005, 2007 phpBB Group • http://www.phpbb.com | |