im thinking i better paint this one blue for all you merc lovers
1-new steel sleeve the rest are chrome, picked up the block today put the crank and pistons in, next mission is to seal it up and put the carbs and electronics on.
| HPBCANADA.COM http://ww.w.hpbc.ca/ |
|
| project dark side mod vp carb http://ww.w.hpbc.ca/viewtopic.php?f=20&t=2086 |
Page 1 of 9 |
| Author: | BoomerMuskoka [ April 7th, 2014, 10:30 pm ] |
| Post subject: | project dark side mod vp carb |
im thinking i better paint this one blue for all you merc lovers 1-new steel sleeve the rest are chrome, picked up the block today put the crank and pistons in, next mission is to seal it up and put the carbs and electronics on.
|
|
| Author: | 13Checkmate [ April 8th, 2014, 11:23 am ] |
| Post subject: | Re: project dark side mod vp carb |
What pistons did you run in the chrome cylinders and what did you run in the steel sleeved cylinder? Cast or forged pistons? I was told to watch mixing the types between the two cylinder types, exception being my bp might be nikasil ( haven't pulled the good head to check) |
|
| Author: | BoomerMuskoka [ April 8th, 2014, 1:11 pm ] |
| Post subject: | Re: project dark side mod vp carb |
im running art pistons in the 5 chrome bores and cv tech supplied a wsm piston when they did the sleeve. |
|
| Author: | 13Checkmate [ April 8th, 2014, 5:30 pm ] |
| Post subject: | Re: project dark side mod vp carb |
Were you able to tell if they were cast or forged? I'm not sure what I'd be best to run in the bp. Ill pull the head on Friday when I get home to check if the good side has been sleeved. |
|
| Author: | DoktorC [ April 8th, 2014, 7:51 pm ] |
| Post subject: | Re: project dark side mod vp carb |
ART and the WSM pistons are both cast.. |
|
| Author: | 3bilgepumps [ April 9th, 2014, 9:27 am ] |
| Post subject: | Re: project dark side mod vp carb |
Boomer, is this why you didn't show up to finish off your 3rd final and last snowmobile in the field day? And what are you putting this new merc on? |
|
| Author: | BoomerMuskoka [ April 9th, 2014, 1:13 pm ] |
| Post subject: | Re: project dark side mod vp carb |
3bilgepumps wrote: Boomer, is this why you didn't show up to finish off your 3rd final and last snowmobile in the field day? And what are you putting this new merc on? im pissed sled is ready to go, i have no truck so i couldnt make it.. 2 trucks in the shop same day wtf, im about to strap the f7 to the roof of my golf. and the modvp i dunno looks sweet on the bench
|
|
| Author: | DoktorC [ April 9th, 2014, 4:52 pm ] |
| Post subject: | Re: project dark side mod vp carb |
BoomerMuskoka wrote: and the modvp i dunno looks sweet on the bench There's a good reason for that 
|
|
| Author: | BoomerMuskoka [ April 10th, 2014, 4:42 pm ] |
| Post subject: | Re: project dark side mod vp carb |
     ta daaaa |
|
| Author: | BoomerMuskoka [ April 10th, 2014, 4:44 pm ] |
| Post subject: | Re: project dark side mod vp carb |
DoktorC wrote: BoomerMuskoka wrote: and the modvp i dunno looks sweet on the bench There's a good reason for that i figure if i paint it blue it might last a little longer.
|
|
| Page 1 of 9 | All times are UTC - 5 hours [ DST ] |
| © 2000, 2002, 2005, 2007 phpBB Group • http://www.phpbb.com | |