| HPBCANADA.COM http://ww.w.hpbc.ca/ |
|
| 30 yamaha performance prop http://ww.w.hpbc.ca/viewtopic.php?f=36&t=4228 |
Page 1 of 1 |
| Author: | MarkStein [ August 28th, 2019, 11:21 am ] |
| Post subject: | 30 yamaha performance prop |
Hey Guys id like to revisit this and see if I can find a prop for Zachs voodoo. A couple guys have offered some to try but that little 30 Yamaha has a diff spline then the merc. Ultimately would like something 14-16 pitch and prefer a chopper. I saw some Ron Hill stuff but they were all cleavers. I would try one if one was available local Thanks guys! Mark |
|
| Author: | David [ August 28th, 2019, 3:32 pm ] |
| Post subject: | Re: 30 yamaha performance prop |
you could try Hill Marine. He advertises lots of small motor props on Ebay their website has a number (800) 762-0309 |
|
| Author: | MarkStein [ August 28th, 2019, 7:55 pm ] |
| Post subject: | Re: 30 yamaha performance prop |
David wrote: you could try Hill Marine. He advertises lots of small motor props on Ebay their website has a number (800) 762-0309 Ya I checked out his Ebay store and it only showed cleavers. I should give them a call. Thank you! |
|
| Author: | Hounddog [ August 31st, 2019, 8:29 am ] |
| Post subject: | Re: 30 yamaha performance prop |
You can change the hub to a 30 hp yamaha in the smaller Mercury chopper. Most times you can use the same chopper on the 30 and the 50 yamaha because of the lower gear ratio in the 50 hp. You only need to change the hub for each motor. The spline on the 50 yamaha is the same as the mercury. Since this prop was on a 50 mercury, it will fit the 50 yamaha. You will need to put a 30 yamaha hub in it. https://www.kijiji.ca/v-powerboat-motor ... nFlag=true |
|
| Author: | MarkStein [ September 2nd, 2019, 8:31 pm ] |
| Post subject: | Re: 30 yamaha performance prop |
Hounddog wrote: You can change the hub to a 30 hp yamaha in the smaller Mercury chopper. Most times you can use the same chopper on the 30 and the 50 yamaha because of the lower gear ratio in the 50 hp. You only need to change the hub for each motor. The spline on the 50 yamaha is the same as the mercury. Since this prop was on a 50 mercury, it will fit the 50 yamaha. You will need to put a 30 yamaha hub in it. https://www.kijiji.ca/v-powerboat-motor ... nFlag=true For sure ya thank you! Reached out to Thom Bucknell, he is bringing one up to Peterborough for us! Looking forward to trying it!. On that note, how is the stock jetting on those 30 Yamahas Don? This motor seems really fat to me right through |
|
| Author: | Hounddog [ September 3rd, 2019, 7:57 am ] |
| Post subject: | Re: 30 yamaha performance prop |
MarkStein wrote: On that note, how is the stock jetting on those 30 Yamahas Don? This motor seems really fat to me right through The jetting is fine on the 30 yamaha.......most outboards run on the fat side, manufacturers would sooner be safe than sorry.....the 30 yamaha is only 30 cubic inches so it will take a while to get the chopper up to speed....... |
|
| Author: | MarkStein [ September 3rd, 2019, 10:00 am ] |
| Post subject: | Re: 30 yamaha performance prop |
Hounddog wrote: MarkStein wrote: On that note, how is the stock jetting on those 30 Yamahas Don? This motor seems really fat to me right through The jetting is fine on the 30 yamaha.......most outboards run on the fat side, manufacturers would sooner be safe than sorry.....the 30 yamaha is only 30 cubic inches so it will take a while to get the chopper up to speed....... Thank you sir! |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| © 2000, 2002, 2005, 2007 phpBB Group • http://www.phpbb.com | |