| HPBCANADA.COM http://ww.w.hpbc.ca/ |
|
| 13 FT Florida Larry R..Allison with Mod 59 cubic inch Merc http://ww.w.hpbc.ca/viewtopic.php?f=41&t=4740 |
Page 1 of 1 |
| Author: | Hounddog [ February 25th, 2025, 4:55 pm ] |
| Post subject: | 13 FT Florida Larry R..Allison with Mod 59 cubic inch Merc |
https://www.facebook.com/groups/boatracinggaragesales/ 13’ Allison, has a built 40hp Merc with 215 compression, boat will do 74+ mph, has a few scuff marks from pulling up to sandbars, title in hand, sea star steering, 6” hydro dynamic jack plate, 3 gallon fuel tank, 36v trim, has allison cover over foam seat. Motor has to run on race fuel, NO PUMP GAS! Shoot me an offer worse I can say is no. Will separate for the right price, or trade for a nice aluminum rig! |
|
| Author: | Hounddog [ February 26th, 2025, 5:03 pm ] |
| Post subject: | Re: 13 FT Florida Larry R..Allison with Mod 59 cubic inch M |
I was asked what I thought about this package. It is likely a low to mid 70mph boat as the ad states. Very fast for a 59 cubic inch mercury. There are several of Larry’s Allisons up here in the region. They perform extremely well. Most boats have had issues with the quality of the build and delaminating fiberglass issues are common. The seller doesn’t say who the engine builder was. The motor must have Jeff Dunn pistons to have that high a compression and he could have built the motor. We haven’t seen any recent built high compression 59 cubic inch Mercury motors in the last ten years. I don’t know of any in Ontario. There was a thread on this site about these Mod 59 Mercurys . http://www.hpbc.ca/viewtopic.php?f=19&t=4261 Certainly if your a got to have mercury guy or girl it’s a good package, but very expensive in Canadian dollars! |
|
| Author: | Hounddog [ February 27th, 2025, 12:06 am ] |
| Post subject: | Re: 13 FT Florida Larry R..Allison with Mod 59 cubic inch M |
https://www.facebook.com/share/1AEcyZRm ... tid=wwXIfr 2004 built 40 merc, 215lbs of compression, has custom sleeves, lightened fly wheel, and a few other things, short shaft 1.83 gears, low water pick up, can also throw in a 2.1 lower and another mid section,. |
|
| Author: | sharpeye Mike [ February 27th, 2025, 10:47 am ] |
| Post subject: | Re: 13 FT Florida Larry R..Allison with Mod 59 cubic inch M |
Is Larry the same guy that builds the 15' allyshot? |
|
| Author: | Hounddog [ February 27th, 2025, 11:13 am ] |
| Post subject: | Re: 13 FT Florida Larry R..Allison with Mod 59 cubic inch M |
sharpeye Mike wrote: Is Larry the same guy that builds the 15' allyshot? No, Jack Barsh and Full Throttle Powerboats built the Ally-Shot |
|
| Author: | sharpeye Mike [ February 27th, 2025, 11:53 am ] |
| Post subject: | Re: 13 FT Florida Larry R..Allison with Mod 59 cubic inch M |
Thanks Don |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| © 2000, 2002, 2005, 2007 phpBB Group • http://www.phpbb.com | |