NEEDED: 3 Cyl. OMC SS

voo-doo_child · **Joined:** April 21st, 2014, 9:59 am **Posts:** 185

Looking for a good complete running motor to put on a voo doo. I am trying to race this season so would like to be somewhat competitive.

Thank you

Hounddog · **Joined:** April 3rd, 2012, 1:52 pm **Posts:** 3167

I did reply to your message. Just a suggestion. IF your VooDoo is a 24 transom model you could do this.
Run an older style 20 inch mid. The solid mounts used on the SS fit, Still run a nitro foot. You will need to lengthen the drive shaft. TOP GUN may have one already done in stock. The parts are cheap and you can use factory trim. You do not need to cut the transom down or run a lowered set back. The boat handles fine. You end up with a long shaft SST 60. I made one up years ago and it worked great.

Here is an example
http://www.ebay.com/itm/1974-70-Johnson ... 35bcea2687

voo-doo_child · **Joined:** April 21st, 2014, 9:59 am **Posts:** 185

Hi Don,

The voo doo is a factory race boat with the cut down transom. The long shaft application is not ideal.

TopGun · **Posted:** May 2nd, 2014, 2:51 pm

yepppp

Hounddog · **Joined:** April 3rd, 2012, 1:52 pm **Posts:** 3167

voo-doo_child wrote:

Hi Don,

The voo doo is a factory race boat with the cut down transom. The long shaft application is not ideal.

Is that the boat that ran a 650XS. It was a short transom and later they ran a long shaft?

voo-doo_child · **Joined:** April 21st, 2014, 9:59 am **Posts:** 185

Not sure about that Don. It was owned by Tim Wilson of Six Mile and had a ss stinger once upon a time. that was probably 20 years ago.

i looked over the boat this morning and decided pass. the seller wanted to 2500 boat and motor (86 clamshell 60 rebuild). 2 stringer had been notched out for a floor at one point and were rotten and broken. The other stringers were full of screws and likely in the same shape. The transom has a butcher of a cut down job and starting to delaminate, bottom was beat.

its too bad, i was looking forward to getting back in a boat.

voo-doo_child · **Joined:** April 21st, 2014, 9:59 am **Posts:** 185

Don,

I believe you are referring to the "Georgian Bay Performance" Voo Doo. That boat was owned by Tim Topping of Six Mile and had a 650 xs. It was sold a number of years ago with a Long OMC on it. Thats how it remains today.

Hounddog · **Joined:** April 3rd, 2012, 1:52 pm **Posts:** 3167

voo-doo_child wrote:

Don,

I believe you are referring to the "Georgian Bay Performance" Voo Doo. That boat was owned by Tim Topping of Six Mile and had a 650 xs. It was sold a number of years ago with a Long OMC on it. Thats how it remains today.

Yes, that is the one I was thinking of. . Is the VooDoo you looked at a white with red insert comp boat? If so that was Steve Wrong's first EP boat.

voo-doo_child · **Joined:** April 21st, 2014, 9:59 am **Posts:** 185

This one was white with black metal flake. i cant post a picture because the forum has met its upload quota. send me a note with your email and i will send over a pic

DoktorC · **Posted:** May 5th, 2014, 5:16 pm

voo-doo_child wrote:

This one was white with black metal flake. i cant post a picture because the forum has met its upload quota. send me a note with your email and i will send over a pic

use photobucket or tinypic...it'll make your internet life easier

.

HPBCANADA.COM

NEEDED: 3 Cyl. OMC SS

Who is online