It is currently November 24th, 2024, 8:49 pm

Martini 26 build

 View active topics

Board index » GENERAL » PROJECT SECTION

All times are UTC - 5 hours [ DST ]

Post new topic Reply to topic  Page 18 of 32
  [ 318 posts ]  Go to page Previous  1 ... 15, 16, 17, 18, 19, 20, 21 ... 32  Next
  Print view Previous topic | Next topic 
Author Message
BoomerMuskoka
 PostPosted: November 26th, 2013, 7:22 pm   
Member
User avatar

Joined: August 12th, 2012, 8:37 pm
Posts: 2699
Location: lake Muskoka
Supermitchie wrote:
I am installing them in the next week or two... I'm confident that they rob top end. But I think it will be worth it. Jules hates the Lean... lol.


mitchie if you look at this pic of me passing you, :mrgreen: you will notice that part of your hull will be out of the water a top speed so it shouldnt rob any top end. :lol: Image

_________________
Image
89 excel 91 valero,81mph sold
1988 baja x 15, chopped to 13'11" modvp Bridgeport 91mph
19' tempest picklefork 84 mod vpcarb 102mph

Top
 Profile Send private message  
OneCycle
 PostPosted: December 4th, 2013, 11:46 am   
HPBC PRESIDENT
User avatar

Joined: March 30th, 2012, 2:25 pm
Posts: 2392
Location: Barrie, On
So this year the Martini is going through a Complete Rebuild

New Stringers
New knees
New Floor
New Interior
New setback for twins
New Paint
and the cherry on top, twin 250xs

This thing will be bad to the bone.


Image

Image

Image
Top
 Profile Send private message  
OneCycle
 PostPosted: December 4th, 2013, 8:56 pm   
HPBC PRESIDENT
User avatar

Joined: March 30th, 2012, 2:25 pm
Posts: 2392
Location: Barrie, On
Just finished cutting the stringers out...
Image

Image

Image
Top
 Profile Send private message  
BoomerMuskoka
 PostPosted: December 4th, 2013, 8:58 pm   
Member
User avatar

Joined: August 12th, 2012, 8:37 pm
Posts: 2699
Location: lake Muskoka
sweeet :lol: i wish i could work on my boats right now. :(

_________________
Image
89 excel 91 valero,81mph sold
1988 baja x 15, chopped to 13'11" modvp Bridgeport 91mph
19' tempest picklefork 84 mod vpcarb 102mph

Top
 Profile Send private message  
DoktorC
 PostPosted: December 4th, 2013, 9:01 pm   
HPBC PRESIDENT
User avatar

Joined: March 31st, 2012, 5:53 pm
Posts: 3548
Location: Lapping lil charger
What are you putting back in?

_________________
08 SRV w/3.1 Hydro-tec Phase lll

I've got enough torque to tear a hole....in time...

Top
 Profile Send private message  
OneCycle
 PostPosted: December 4th, 2013, 9:21 pm   
HPBC PRESIDENT
User avatar

Joined: March 30th, 2012, 2:25 pm
Posts: 2392
Location: Barrie, On
DoktorC wrote:
What are you putting back in?


its going to BCB for new stringers, knees and floor.. im sure the'll figure it out.

what are you thinking ?
Top
 Profile Send private message  
DoktorC
 PostPosted: December 4th, 2013, 9:35 pm   
HPBC PRESIDENT
User avatar

Joined: March 31st, 2012, 5:53 pm
Posts: 3548
Location: Lapping lil charger
OneCycle wrote:
DoktorC wrote:
What are you putting back in?


its going to BCB for new stringers, knees and floor.. im sure the'll figure it out.

what are you thinking ?


A few sheets of Baltic and a bucket of vinyl...but mostly I'm thinking how happy I am that I'm far away lol.

_________________
08 SRV w/3.1 Hydro-tec Phase lll

I've got enough torque to tear a hole....in time...

Top
 Profile Send private message  
OneCycle
 PostPosted: December 4th, 2013, 10:11 pm   
HPBC PRESIDENT
User avatar

Joined: March 30th, 2012, 2:25 pm
Posts: 2392
Location: Barrie, On
DoktorC wrote:
OneCycle wrote:
DoktorC wrote:
What are you putting back in?


its going to BCB for new stringers, knees and floor.. im sure the'll figure it out.

what are you thinking ?


A few sheets of Baltic and a bucket of vinyl...but mostly I'm thinking how happy I am that I'm far away lol.



yeah its not all that bad... motor is coming off saturday likly for good.. the real challenge will be tring to find a nice dual shifter and throttle that fit... prob end up getting BCB to re-do the dash a bit... gauge cluster stays the same except GPS is getting replaced with another RPM gauge.. then he'll run a GPS like mithchies Super boat..
Top
 Profile Send private message  
DoktorC
 PostPosted: December 4th, 2013, 10:23 pm   
HPBC PRESIDENT
User avatar

Joined: March 31st, 2012, 5:53 pm
Posts: 3548
Location: Lapping lil charger
You'll have to either change the dash to fit the shifter or go with a OEM style shift/throttle with only two sticks (like Jordan had). It's tight in there...

The helm probably needs an upgrade too..I'm not sure if the standard helm will push two HP 3L's...especially if you have to drive the thing.

_________________
08 SRV w/3.1 Hydro-tec Phase lll

I've got enough torque to tear a hole....in time...

Top
 Profile Send private message  
OneCycle
 PostPosted: December 4th, 2013, 11:48 pm   
HPBC PRESIDENT
User avatar

Joined: March 30th, 2012, 2:25 pm
Posts: 2392
Location: Barrie, On
Kevin will have to make a judgement call on the steering. My guess is it will have a link like the previous twin setup and only have one hydraulic cylinder.
Top
 Profile Send private message  
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 18 of 32
  [ 318 posts ]  Go to page Previous  1 ... 15, 16, 17, 18, 19, 20, 21 ... 32  Next

Board index » GENERAL » PROJECT SECTION

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 12 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  


Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Style originally created by Volize © 2003 • Redesigned SkyLine by MartectX © 2008 - 2010