Vision Rebuild

Wideopen · **Posted:** May 6th, 2015, 10:36 pm

sure man sounds good. I think this has been an project since ive joined fbc a couple years ago so im excited to see it go!

BoomerMuskoka · **Posted:** May 6th, 2015, 11:27 pm

idvette wrote:

Got an answer on s&f that sounds about right, 39psi. I'll source an adjustable regulator somewhere, but I'll take the pump off you for sure please

toss the vst

idvette · **Posted:** May 7th, 2015, 6:42 am

BoomerMuskoka wrote:

idvette wrote:

Got an answer on s&f that sounds about right, 39psi. I'll source an adjustable regulator somewhere, but I'll take the pump off you for sure please

toss the vst

Long gone

idvette · **Posted:** May 9th, 2015, 8:29 am

[url][URL=http://s1066.photobucket.com/user/08BlackBigHorn/media/88%20Hydrostream%20Vision/74C5CCC0-ACEE-4B3A-9134-1E26753F9F30.jpg.html]

[/url][/url]

She's back! Time to get rigging

AE21 · **Joined:** July 12th, 2015, 11:32 pm **Posts:** 30

beavertonae-21 wrote:

Bring
Out
Another
Thousand

LOL Been there, dual cable steering is such a rip off to buy new now , unless you can find a good used setup I would go hydrallic and get it done for good.

I have a complete dual rack ride guide that works fine, i'll be pulling out of my AE21, just don't have the motor tubes and linkages gave them to a buddy,but have helm,racks and cables, with an antique quicksilver plastic wheel

idvette · **Posted:** July 28th, 2018, 8:59 pm

And just like that a few years go by lol... Well I'm back at it again. Bought a bridgeport cowl, tore the motor down, ordered all my gaskets and new reeds. Cleaned, wet sanded and painted the mid and cowl, ready for re-assembly and rigging. Going to mount the mid and powerhead tomorrow, should motivate me to finish it! Will be filling in the dash and going centre steer before I hit the water. Might not be pretty this year, but we have a race in 2 weeks I hope to be ready for!

KAL Racing · **Joined:** April 8th, 2012, 8:11 am **Posts:** 1297

If you do you go center steer don’t fill-in the other hole because you may want to go back… I tried it like it but my passengers prefer the front seat ... I am going back to the side by side front seating

idvette · **Posted:** June 23rd, 2019, 9:03 am

Well it's been almost a year, been picking away at the boat. It is now centre steer with dual opposed ride guide, single Murph seat (for now, I have the other one to be mounted in tandem), motor is together and wired, dash holes have all been filled, I built a hotfoot mount with integrated dead pedal and battery mount, fuel tank mounting pad has been installed. Vst and oil pump delete, I have RFCB's old Weldon fuel pump ready to install with AN lines and fittings to the motor. Found a 2 hole CLE lower, block sanded it and getting it ready to repaint. Bridgeport pan installed, cowl in the body shop at work getting painted. Another solid day or 2 of work and it should be all back together! Sorry no pics, since that hosting site started charging I haven't found another way. Pics on Facebook though.

talonkid · **Joined:** April 2nd, 2012, 10:55 am **Posts:** 327

Sounds like its looking good to go for North Bay!

idvette · **Posted:** June 24th, 2019, 8:17 am

It'll be in North Bay come hell or high water lol

HPBCANADA.COM

Vision Rebuild

Who is online